BEST ACCESS SYSTEMS 35HW Servisní příručka Strana 120
- Strana / 228
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Service and Maintenance for Cylindrical Locks
5–10 W Series Service Manual
Task B. To adjust for the door’s thickness:
1. Determine the door’s thickness.
2. Pull the rose locking pin and rotate the outside rose liner until the
proper groove on the through-bolt stud lines up with the hub face.
Note 1: Make sure that the locking pin fully locks into the rose liner.
Note 2: The lock fits doors 1 3/4″ to 2 1/4″ thick.
(A spacer is available for 1 3/8″ doors.)
Figure 5.11 Adjusting the outside liner for the door thickness
1 3/4″
2″
2 1/4″ groove
Through-bolt stud
Hub face
Outside rose liner
Rose locking pin
- CREDITS/COPYRIGHT 2
- CONTENTS 3
- Contents 4
- W Series Service Manual v 5
- W Series Service Manual vii 7
- W Series Service Manual ix 9
- GETTING STARTED 11
- DOCUMENTATION PACKAGE 13
- TECHNICAL SUPPORT 14
- IDH MAX LOCKS FUNCTIONS 15
- FUNCTION DESCRIPTIONS 16
- W Series Service Manual 2–3 17
- TRIM COMPONENTS 19
- Proximity card 20
- W Series Service Manual 2–7 21
- W Series Service Manual 2–8 22
- Magnetic stripe 23
- 2–10 W Series Service Manual 24
- W Series Service Manual 2–11 25
- SCREW KITS 27
- Lower escutcheon 28
- Access door 28
- READER CONVERSION 29
- MORTISE CASE EXPLODED DIAGRAM 31
- Mortise case parts 32
- OTHER MORTISE LOCK COMPONENTS 33
- 2–20 W Series Service Manual 34
- Cylindrical chassis 35
- Other cylindrical 36
- Panel interface 37
- 2–24 W Series Service Manual 38
- ELECTRIFIED LOCKS FUNCTIONS 39
- W Series Service Manual 3–3 41
- W Series Service Manual 3–5 43
- 3–6 W Series Service Manual 44
- W Series Service Manual 3–7 45
- 3–8 W Series Service Manual 46
- Mortise case 48
- 3–12 W Series Service Manual 50
- 8W COMPONENTS DIAGRAM 53
- 3–16 W Series Service Manual 54
- MORTISE LOCKS 55
- IDH Max Mortise 57
- Upper escutcheon screw 60
- Lower escutcheon screw 60
- Inside escutcheon 60
- W Series Service Manual 4–9 63
- Spindles 75
- Set screw 75
- Cylinder clamp screw 82
- Lock case 82
- Mortise cylinder wrench 83
- Cylinder 83
- Cylinder ring 83
- Spanner wrench 84
- Rose ring 84
- 4–34 W Series Service Manual 88
- Figure-8 opening 91
- Changing hand and 94
- LH RH LHRB RHRB 95
- Tasks for changing 97
- Switch bracket feet 98
- Actuator button 98
- Wire strain relief 98
- Pivot point on the RQE switch 100
- Flat side of the outside hub 100
- Screw post 101
- Auxiliary bolt 101
- Latchbolt 101
- Anti-friction latch lever 101
- Replacing the 105
- Removing the solenoid 105
- Reinstalling the solenoid 105
- Replacing the RQE 106
- Removing the RQE switch 106
- Reinstalling the RQE switch 107
- Replacing the door 107
- Replacing the latch 109
- SERVICE AND MAINTENANCE 111
- CYLINDRICAL LOCKS 111
- Removing 113
- IDH Max cylindrical 113
- Lever shaft 114
- Security screw 114
- Reinstalling 118
- Wire Color 119
- W Series Service Manual 5–13 123
- Reader wire harness 124
- Outside of door 124
- Inside of door 126
- Blocking plate 127
- Throw member 127
- Control key 128
- Insert the screwdriver here 130
- Figure-8 core hole 130
- Lever keeper 130
- Through-bolt 133
- Rose liner 133
- Lever handle 134
- Chassis type Part number 135
- RQE rose liner Part number 135
- Wire hole 138
- Door status switch 138
- Door jamb 138
- Door status sensor White 2 2 139
- 5–30 W Series Service Manual 140
- ADDITIONAL SERVICE AND 141
- MAINTENANCE FOR IDH MAX 141
- REPLACING WIRE HARNESSES 142
- Removing and 143
- Harness clamp 144
- Lower left mounting screw 144
- REPLACING READERS 151
- Outside escutcheon 155
- Reader gasket 155
- Location of prongs 155
- 6–18 W Series Service Manual 158
- GLOSSARY 159
- Glossary 160
- A–2 W Series Service Manual 160
- W Series Service Manual A–3 161
- A–4 W Series Service Manual 162
- INSTALLATION INSTRUCTIONS 163
- Installation Instructions 164
- B–2 W Series Service Manual 164
- Overview Contents 165
- Indianapolis, Indiana 166
- BEST ACCESS SYSTEMS 167
- 1 Mark centerlines 168
- 4 Drill holes 170
- 9 Install mortise case 173
- 10 Install mounting plates 173
- 17 Install access door 179
- IDH Panel Interface 182
- 5 Install latch 195
- 10 Remove outside knob/lever 198
- 11 Adjust for door thickness 198
- Connect reader wire harness 201
- 19 Install access door 204
- 25 Mark centerlines 213
- 26 Center punch drill points 213
- 27 Install strike plate 213
- 28 Drill holes 214
- 30 Install mortise case 215
- 32 Install knobs or levers 216
- 33 Install core 216
- Electrical requirements 217
- Parts List 217
- Wiring diagram 217
- ½ times greater than 218
- ½ = 54 volt-amps 218
- 7 Install strike plate 220
- 8 Install core 220
- 5 Engage retractor in latch 220
- Parts list 221
- ½ = 33.48 volt-amps 222
- Numerics 223
- C-2 W Series Service Manual 224
- W Series Service Manual C-3 225
- C-4 W Series Service Manual 226
- W Series Service Manual C-5 227
- C-6 W Series Service Manual 228
Související produkty a manuály pro Bezpečnostní dveřní ovladače BEST ACCESS SYSTEMS 35HW
(8 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce